Can I Set Up a Tub Myself? Considerations As Well As Steps
Can I Set Up a Tub Myself? Considerations As Well As Steps
Blog Article
They are making several great points related to How to Install a Bathtub as a whole in the content down the page.
Mounting a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is easily easily accessible, the task can move speedily; if you have to open up a wall to get rid of the old bathtub as well as place the brand-new bathtub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will assist you mount a new bath tub in your bathroom if you have currently bought a brand-new tub as well as do not need to alter the setup of your previous supply of water pipelines.
Your devices and product list ought to consist of the following:
Planning for the Installation
Firstly, the supporting structure provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps system to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is detach the supply of water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. Once the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Prior to going on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bath tub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; then do the exact same for the other tap.
Activate the water system and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Fill up the bathtub as well as likewise check the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub ought to wait until the bath tub has been made use of a minimum of when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines are in location in between the tap as well as the sink. Secure the tap in position with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to complications with moisture and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealant can crack rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or waterproof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader on Installing A Bathtub, I figured sharing that piece of content was a good idea. I beg you take the time to distribute this blog posting if you appreciated it. Many thanks for taking the time to read it.
Start Now
Report this page